Skip to main content

Connect Via SDI

🔌 SDI Guide← Back to Quick Start

This guide covers setting up the Move 4K with 3G-SDI video output. Use this for long cable runs (up to 100m) in professional or broadcast environments.

📋What you need
  • SDI cable (75-ohm BNC)
  • 12V DC power supply (included) or PoE+ switch/injector
  • A video switcher, capture card, or monitor with SDI input
  • Optional: Ethernet cable for network control

Step 1: Connect the SDI Cable​

  1. Connect a 75-ohm SDI cable (BNC) from the camera's SDI output to your video switcher, capture card, or monitor's SDI input.
📋Use proper SDI cables

Standard composite or component BNC cables will not carry an SDI signal reliably. Use 75-ohm SDI-rated cable.

Step 2: Power the Camera​

Choose one of the following power methods:

Option A: 12V DC Power Supply​

  1. Connect the included 12V DC power supply to the camera's DC input.
  2. Plug the power supply into a standard wall outlet.

Option B: Power over Ethernet (PoE+)​

  1. Connect an Ethernet cable from a PoE+ (802.3at) switch or PoE+ injector to the camera's LAN port.
  2. The camera will power on automatically.
⚠️PoE+ required

Ensure your switch or injector supports PoE+ (802.3at), not just PoE (802.3af).

Step 3: Wait for the Camera to Boot​

Once powered, the camera performs a startup sequence:

1️⃣
Self-calibration — The camera moves through its full range of motion. This is normal.
2️⃣
Home position — The camera returns to Preset 0 (Home).
3️⃣
Ready — The front LED turns solid green. You should see video on your SDI display.

Step 4: Control the Camera​

With SDI, the camera is likely distant from your control area. Use one of these control methods:

If you connected an Ethernet cable to the camera's LAN port:

  1. Open a browser and go to http://ptzoptics.local/
  2. Log in with username admin and set a password.
  3. Use the Horizon web interface for full PTZ control, image settings, and preset management.

Option B: RS232 Control​

Connect an RS232 cable from your controller or joystick (such as the PTZOptics SuperJoy) to the camera's RS232 Input port.

⚠️Pinout compatibility

RS232 pinouts vary between manufacturers. If pinouts differ, you may need a null modem adapter or custom cable.

Option C: IR Remote​

The included IR remote works for basic control, but is not recommended for distant cameras since it requires line-of-sight.

Step 5: Save Your First Preset​

Using the Web Interface​

  1. Move the camera to your desired position.
  2. Click Set in the Preset Control section.
  3. Enter a preset number and press Enter.

Using a PTZ Joystick (SuperJoy)​

  1. Move the camera to your desired position.
  2. Press the Preset button on the joystick.
  3. Enter the preset number and confirm.
ℹ️What presets save

A preset saves both the camera position and all image settings. Calling a preset restores both.

3G-SDI Specifications​

FeatureSpecification
Max Resolution1080p @ 60fps (1920 × 1080)
Max Cable Length~200–328 ft (60–100 m) with quality cable
Audio❌ No — SDI does not carry audio on the Move 4K. Use HDMI, USB, or IP for audio.
ConnectorsBNC (locking)
Signal Type3G-SDI (Level-A or Level-B)
⚠️No 4K over SDI

The Move 4K's SDI output is limited to 1080p. If you need 4K, use HDMI, USB, or IP/Network streaming instead.

Next Steps​

← Back to Quick Start