Getting Started with the Move SE

Choose Your Power MethodConnect to Your NetworkSet Your PresetsSTREAM

Step 1: Power & Connect ~3 minutes

See tabs below:

AC Adapter

1. Connect the included power adapter to the DC IN port on the back of the camera.
2. Plug the adapter into a power outlet.

Power over Ethernet

To power this camera over Ethernet, you will need a power-over-Ethernet switch or power-over-Ethernet injector.

1. Connect an Ethernet cable from a Power over Ethernet switch to the camera's LAN port.

When powered on, the camera performs a short startup sequence moving through its full range of motion. This is normal. It will return to Preset 0 (Home) when complete.

Connect a video output to verify the camera is working:

• HDMI 1.3: direct to a display or capture card
• 3G-SDI: to an SDI-compatible device (HDMI and SDI are not simultaneous)
• USB: to your computer using the included USB C-A cable
• IP Video Connection: To verify your video connection on your network, follow the instructions in Step 2 below. This will allow you to view the camera’s video feed

→ Full details: Power · Connections

Troubleshooting: Camera doesn't start up

• Verify the power adapter is firmly seated in the DC IN port.
• If using PoE, confirm your switch supports PoE (802.3af).
• Try a different power outlet or Ethernet port on your switch.
• Check that the power LED on the rear of the camera illuminates.

Step 2: Get On the Network ~5 minutes

Use the tabs to view the two methods for connecting to the camera over your network.

Web Browser

Open any web browser and go to:

http://ptzoptics.local

This uses mDNS to automatically discover your camera. This will take you to the camera’s Web User Interface. If it loads, you're connected. You should be able to see your camera’s video feed.

IR Remote

With HDMI connected to a display, press on the IR remote:

[*] → [#] → [4]

The camera's IP address will appear on screen.

Setting up multiple cameras?

Do one at a time. Assign each a unique Device ID from the Web UI's Device Info tab so you can reach them by name, e.g., http://camera-one.local and http://camera-two.local.

→ Full details: Networking

Troubleshooting: Can't find the camera

• ptzoptics.local doesn't work? Your network may not support mDNS. Use the IR Remote method instead.
• Camera and computer on different subnets? Both must be on the same network range (e.g., both on 192.168.1.xxx).
• Firewall blocking? Temporarily disable firewall and try again.
• Need your network range? For typical users, on Windows, open Command Prompt and run ipconfig. On Mac, open Terminal and run ipconfig getifaddr en0. Look for your IPv4 address; the first three octets are your network range.
  • If you are experiencing difficulties or you are unsure of your network type, please contact your IT administrator.

Step 3: Access the Web UI ~2 minutes

Open a web browser and enter your camera's IP address:

http://[your-camera-ip]

You'll see a login screen.

important

If this is your first time logging in, you will be prompted to create a new password.

Username: The username is admin Password: Enter your Password

Once logged in, you have full control of your camera, including PTZ, image settings, streaming, presets, and more.

You're all set!

Your Move SE is powered, networked, and accessible from your browser. Explore the sections below to configure streaming, set presets, and unlock every feature.

→ Full details: Web UI Documentation

Troubleshooting: Can't reach the Web UI

• Double-check the IP address. No https, just http://
• Try a different browser (Chrome, Firefox, Edge)
• Clear your browser cache or try an incognito/private window
• Confirm your computer is on the same network subnet as the camera
• If you've forgotten your password, you can factory reset network settings using the IR remote: [*] → [#] → [MANUAL]

Quick Reference

What's in the Box

• Move SE Camera
• AC Power Supply
• USB C-A Cable
• RS-232C Cable
• Quick Start Guide
• IR Remote
• 2 AAA Batteries
• Lens Cap

Part Numbers

PTxxx-SE-xx-G3

Color	Zoom	Part Number
Gray	12X	PT12X-SE-GY-G3
Gray	20X	PT20X-SE-GY-G3
Gray	30X	PT30X-SE-GY-G3
White	12X	PT12X-SE-WH-G3
White	20X	PT20X-SE-WH-G3
White	30X	PT30X-SE-WH-G3

Default Network Info

• IP mode: DHCP (default)
• mDNS address: http://ptzoptics.local
• Username: admin
• Password: set on first login

Control Port Numbers

• UDP: 1259
• TCP: 5678
• Sony VISCA: 52381

IR Remote Shortcuts

Action	Shortcut
Show IP address	[*] → [#] → [4]
Reset IP to DHCP	[*] → [#] → [MANUAL]
Set static IP	[#] → [*] → [#] → [1-9] → assigns 192.168.100.8X

→ Full details: IR Remote Documentation

Need Help?

info

PTZOptics Support — Mon–Thu: 8:00 AM – 6:00 PM ET · Fri: 8:00 AM – 4:00 PM ET

Email: [email protected] · Phone: (484) 593-2584

Troubleshooting Guide · Knowledge Base