Skip to main content

Connect Via HDMI

📺 HDMI Guide← Back to Get Started

This guide covers setting up Rise 4K using an HDMI video output. Use this if you're connecting to a monitor, capture card, or recording device in the same room.

📋What you need
  • HDMI cable
  • 12V DC power supply (included) or PoE++ (802.3bt) switch or injector
  • A monitor, TV, or capture card with HDMI input
  • Optional: Ethernet cable for network control

Connect the HDMI Cable​

  1. Connect an HDMI cable from the camera's HDMI output to your monitor, TV, or capture card's HDMI input.
⚠️HDMI input vs output

Many computers have HDMI outputs only, not inputs. If your computer lacks an HDMI input, use a capture card.

Connect Power and Network​

Choose one of the following power methods:

Option A: 12V DC Power Supply

  1. Connect the included 12V DC power supply to the camera's DC input.
  2. Plug the power supply into a standard wall outlet.

Option B: Power over Ethernet PoE++ (802.3bt)

  1. Connect an Ethernet cable from a PoE++ (802.3bt) switch or PoE++ (802.3bt) injector to the camera's LAN port.
  2. The camera will power on automatically.
⚠️Requirement

Ensure your switch or injector supports PoE++ (802.3bt), not just PoE (802.3af).

Wait for Startup Sequence​

When powered, the Rise 4K camera performs a startup sequence:

1️⃣
Self-calibration: During startup, the camera moves through its full range of motion while both the green (Standby) and blue (Power) LEDs are on. When self-calibration is complete, the camera returns to Preset 0
2️⃣
Ready: Once the camera stops moving and the green LED turns off, your camera is ready to use.

Control the Camera​

Use the following options to quickly verify control of the camera.

Option A: Network Control (Recommended)

If the Rise 4K camera is connected to your network, you can control it from the Horizon Web UI. To do this, you will first need to find the camera on your network:

  1. Open a browser and go to http://ptzoptics.local/
  2. Log in with username admin and set a password.
  3. Use the Horizon Web UI for full PTZ control, image settings, and preset management.

Option B: IR Remote (Simplest)

Use the included IR remote to pan, tilt, zoom, and save presets. Point the remote at the camera's front sensor.

ButtonAction
⬆️⬇️⬅️➡️ Arrow keysPan left/right and tilt up/down
Tele / WideZoom in and out
HomeReturn to Home Position
[PRESET] + [Number]Save a preset

Save Your First Preset​

Using the Web Interface​

  1. Move the camera to your desired position.
  2. Click Set in the Preset Control section.
  3. Enter a preset number and press Enter.
ℹ️What presets save

A preset saves both the camera position and all image settings. Calling a preset restores both.

Using a PTZ Joystick (e.g., SuperJoy)​

  1. Move the camera to your desired position.
  2. Press the Preset button on the joystick.
  3. Enter the preset number and confirm.
ℹ️What presets save

A preset saves both the camera position and all image settings. Calling a preset restores both.

Using the IR Remote​

Press [PRESET] then a number (e.g., [1]) to save. To recall, press the number again. For more information on using the IR remote, see the Using the IR Remote section.

HDMI Specifications​

FeatureSpecification
Max Resolution4K @ 60fps (3840 × 2160)
Max Cable Length~49 ft (15 m) without extenders
Audio✅ Yes — embeds audio from the 3.5mm input
4K RequirementsCapture device must support 4K over HDMI; 4K requires more processing power than 1080p
⚠️More Information on Camera Control

This camera can be controlled using various methods and joystick controllers. To learn more about camera control, see Control Options.

Next Steps​

← Back to Get Started