Skip to main content

Connect Via SDI

This guide covers setting up the Move 4K with 3G-SDI video output. Use this for long cable runs (up to 100m) in professional/broadcast environments.

📋What you need
  • SDI cable (75-ohm BNC)
  • 12V DC power supply (included) or PoE+ switch/injector
  • A video switcher, capture card, or monitor with SDI input
  • Optional: Ethernet cable for network control

Step 1: Connect the 3G-SDI Cable​

  1. Connect a 75-ohm 3G-SDI cable (BNC) from the camera's SDI output to your video switcher, capture card, or monitor's SDI input.
📋Use proper SDI cables

Standard composite or component BNC cables will not carry an SDI signal reliably. Use a 3G 75-ohm-rated cable.

Step 2: Power the Camera​

Choose one of the following power methods:

Option A: 12V DC Power Supply​

  1. Connect the included 12V DC power supply to the camera's DC input.
  2. Plug the power supply into a standard wall outlet.

Option B: Power over Ethernet (PoE+)​

  1. Connect an Ethernet cable from a PoE+ (802.3at) switch or PoE+ injector to the camera's LAN port.
  2. The camera will power on automatically.
⚠️PoE+ required

Ensure your switch or injector supports PoE+ (802.3at), not just PoE (802.3af).

Step 3: Wait for the Camera to Boot​

Once powered, the camera performs a startup sequence:

1️⃣
Self-calibration: During startup, the camera moves through its full range of motion while both the green (Standby) and blue (Power) LEDs are on. When self-calibration is complete, the camera returns to Preset 0 (Home)
2️⃣
Ready: Once the camera stops moving and the green LED turns off, your camera is ready to use.

Step 4: Control the Camera​

With SDI, the camera is likely distant from your control area. Use one of these control methods:

Option A: IR Remote (Simplest)​

Use the included IR remote to pan, tilt, zoom, and save presets. Point the remote at the camera's front sensor.

ButtonAction
⬆️⬇️⬅️➡️ Arrow keysPan left/right and tilt up/down
Tele / WideZoom in and out
HomeReturn to Preset 0
[PRESET] + [Number]Save a preset

If you also connected an Ethernet cable to the camera's LAN port:

  1. Open a browser and go to http://ptzoptics.local/
  2. Log in with username admin and set a password.
  3. Use the Horizon web interface for full PTZ control, image settings, and preset management.
💡Best of both worlds

Use HDMI for video output to your display, and Ethernet for network control. This gives you the quality of HDMI with the convenience of web-based control.

Option C: Serial VISCA Control (RS232 & RS485)​

Connect a serial cable from your controller or joystick (such as the PTZOptics SuperJoy) to the camera's Serial Input port.

⚠️More Information on Serial Control

Serial control supports both RS232 and RS485 connections. To learn more about serial control, see Control Options.

Step 5: Save Your First Preset​

Using the Web Interface​

  1. Move the camera to your desired position.
  2. Click Set in the Preset Control section.
  3. Enter a preset number and press Enter.

Using a PTZ Joystick (SuperJoy)​

  1. Move the camera to your desired position.
  2. Press the Preset button on the joystick.
  3. Enter the preset number and confirm.
ℹ️What presets save

A preset saves both the camera position and all image settings. Calling a preset restores both.

Using the IR Remote​

Press [PRESET] then a number (e.g., [1]) to save. To recall: press the number again. For more information on using the IR remote, see the Using the IR Remote section.

3G-SDI Specifications​

FeatureSpecification
Max Resolution1080p @ 60fps (1920 × 1080)
Max Cable Length~200–328 ft (60–100 m) with quality cable
Audio✅ Yes
ConnectorsBNC (locking)
Signal Type3G-SDI (Level-A or Level-B)
⚠️No 4K over SDI

The Move 4K's SDI output is limited to 1080p. If you need 4K, use HDMI, USB, or IP/Network streaming instead.

Next Steps​

← Back to Get Started